In the 15th year, the double 11 made a half price spike in Jingdong to a Pentium G3460. At the beginning of 16 years, this computer was ruined. At that time, a brand machine at home was too old for the platform, and after a number of upgrades, there was a short board that couldn't meet the final choice of retirement. So according to this piece of Pentium in Jingdong bought accessories (where the power is removed from the brand's machine), installed a host of office and light games.
First, the following configuration: CPU: Pentium G3460 Motherboard: Gigabyte B85M D3H Memory: Zhiqi DDR3 1600 8G Solid State Drive: SanDisk Plus 240G Mechanical Hard Drive: Toshiba 3T 7200 Turn Graphics: Renaissance GTX760 2G
My installed concept is: Under the premise of ensuring the quality and stability of accessories and satisfying the needs of users, try to achieve low power consumption, low heat, low noise, while taking into account the upgrade needs and cost-effective upgrade. I think that in all the accessories of the machine, the motherboard and power supply are the most important, and it is the basis of the whole computer operation and stability. There is no reliable and stable motherboard and power supply. Others like the processor graphics card are no matter how good. All look a bit top-heavy. Currently, this Gigabyte B85M-D3H is more than enough to use with the G3460. Even if it is upgraded to i5 later, it will not be a short board.
Hardware has only poor chassis, because a few computers were installed before, are full-size chassis, put the table under the foot of the situation is very easy to pick gray, so in line with the principle of simple and practical does not take up space, want to choose a can hold down The 29-cm-long M-ATX chassis with the smallest possible size, the appearance of pursuing simple and generous, so that first ruled out all the modeling exaggerated chassis, the price of the metal chassis, such as the first horse, cool the few, the use of materials Kind-hearted are all too big, the smaller iron sheet is thin, finally decided to choose in the aluminum chassis, see Qiao Sibo RM3 can not open a leg, although the volume is bigger than what I requested, the price is more than budget Doubled, but the aluminum body on both sides of the tempered glass styling simple and high value, and the internal line space (said good not to run it!) and the air duct are designed very reasonable, later upgrade is also convenient, think of it Buying a decoration and looking back is also comfortable, so decisively orders. 
However, after receipt of the goods, it was found that although material, structure, design, and workmanship did not have to be said, quality control was a bit daunting (possibly due to cases or logistics). The front panel of the chassis was distorted and not a flat surface. Lead to the top of the chassis there is a gap between the edge of the glass and the front panel left and right upper and lower tolerances, looking at the heart, originally wanted to apply for a replacement, and later thought that this double-sided side through the big glass, which installed lights, not mine Style, and Pentium machine play light is also a bit too tempting; do not install light bar, put the black light out of the fire and waste this chassis. Coupled with the power of non-module wire to see through it will look messy (in fact, all the accessories are not strong enough) so ultimately choose to return. 
JONSBO RM3 silver MINI-MATX chassis (support MATX motherboard / ATX power supply / aluminum shell / double-sided 5.0 thick tempered glass side panels) 589 yuan Jingdong direct link
After that, they strengthened the principles of simplicity, small size, and cost-effectiveness. They also cut off most of their budgets. They gave up all aluminum boxes with side-to-side penetration, and they found Josip again in a circle. No way, the price was right and the model was simple. Textured chassis really can not find too much, fancy two models, one is U3, one is RM2, these two chassis are Qiao Sibo positioning in the end of the M-ATX chassis, plate thickness can also do, RM2 ago The panel has a more reset button, U3 size is smaller, the internal structure and the air duct on the power supply is more reasonable, but the video card is found to be slightly shorter. In order to install the graphics card, you can only give up, so you have chosen Qiao Sibo RM2 - it turns out Again it is a wrong choice.
JONSBO RM2 silver MINI-ATX chassis (support ATX motherboard / aluminum chassis / support 95MM high radiator / 290MM long video card) 299 yuan Jingdong direct link 
JONSBO U3 silver MINI-MATX chassis (support MATX motherboard / aluminum chassis / ATX power supply / 175MM high radiator / 260M long video card) 349 yuan Jingdong direct link 
Let's look at the predecessor of RM1 of Qiao Sibo RM2. There is an optical drive cover on the front panel. There is no cooling hole on the top. The facial value is a plus on the minus points. It is a tie with the RM2, but after the listing, everyone responds that the internal temperature of the chassis is too high. Unable to get out, Joe Schob brainstormed and opened the skylight at the top of the chassis and removed the drive. The 2.0 version was announced.
The design of this chassis may be adhering to the "no design even if the design" principle, the front is a length and width of aluminum 33.5cm * 20.5cm aluminum, there is a slight vertical drawing process, in addition to the left bottom of a row of buttons outside the interface Any design element. After the optical drive cover on the RM1 is removed, the front is more compact and more integrated.
The lower left is the row of power button, restart button (not on U3), and the interface between the two usb3.0 ports is microphone and headphone. The USB3.0 interface at the top is underpowered. When it is connected to a mobile hard disk, it cannot be read normally. The interface below does not have this problem. I do not know if this is an example or a common problem. Because the button interface is centered on the left side of the panel, this case will be easier to operate on the right side of the desktop display. This is one of the reasons why I chose this chassis.
Two buttons with indicator lights, the outer ring will issue a blue light after the boot, the lower restart key taking into account the hard disk indicator, will flash red when the hard disk reads. In addition, there is no other light on the surface of the chassis, which will not cause a lot of light pollution in the dark environment at night, which is my favorite style.
At the top, there are 7 long strips of cooling vents, which are not evaluated for aesthetic reasons. However, compared to a large area of ​​openings, this design will be more secure at least in terms of firmness.
The vents have a black metal dust-proof net.
The bottom is also lined with two vertical cooling vents, three rivets at each end are used to fix the front and rear panels of the fuselage, and four metal feet with rubber pads ensure the distance between the bottom and the desktop, which is conducive to air circulation. However, my four pads are not on a horizontal plane. Placing two planes on either side of the top of the fuselage will have a diagonal effect.
The metal foot is fixed on the body by the center screw
The mechanical hard disk installed at the bottom of the chassis is fixed by four screws from the bottom of the chassis. There are two hard disk installation positions at the bottom of the chassis, and one of the front panel positions is a 2.5-inch hard disk installation position.
Thanks to the sturdiness and yield strength of the 1.8mm-thick aluminum sheet, the rear of the chassis has a large number of heatsinks in addition to the power supply, PCI slots, and I/O flapper, and this design is in the iron chassis. It's hard to see.
Different from the metal nameplate on the RM3. The RM2 only has a product label in the upper left corner of the rear, which is the only label in the entire chassis that can prove the identity of the chassis. Two black screws on the left side of the label are used to fix the aluminum ribs at the top of the chassis. The ribs have a 2.5-inch hard disk position. You need to unscrew the two and the front panel on the right side of the front panel. Screws can be removed to install the hard disk. The right side of the PCI slot, using a removable type, fixed by screws, convenient and beautiful, to avoid some of the chassis can only be left empty over the wrong baffle. It may be seen that some people will ask, video card? Where did you go? Don't worry, then look down.
The lower left-hand corner is the power supply position. People who may be frequently installed see at a glance that the Bestec ATX power supply is different from most current power supply designs on the market. The fan is facing the outside of the chassis rather than the inside. This design also reduces the size of the chassis. The interior itself is turbulent with turbulent air ducts and convection with the radiator located behind the front panel of the chassis (although the effect is minimal). Because the previous brand was old, the removed power supply and the screws above had been rusted, including four screws used to fix the power supply, but because the gasket was added between them, and the aluminum case would not have been rusty. , so I did not care about it. Above the power supply is engraved with the English origin of the Qiao Sibo chassis that has always been: MADE IN CHINA
The right side of the power supply is an I/O shield. The Gigabyte B85M-D3H motherboard contains six USB ports, including two rear USB 3.0 ports. The three HDMI/DVI/VGA display output ports are also convenient for the motherboard. Do not use the card under the condition of using nuclear display.
The governor on the RM1 below the I/O damper was simply allocated, leaving an empty opening for the cooling of the chassis.
The top, the left and the bottom of the chassis are made of a single piece of aluminum plate folded and extended slightly up and down to the right of the chassis to form a C-shaped wrapping structure, which makes the body more sturdy and integral, with fewer joints and more beautiful appearance. However, at the same time, this design resulted in the absence of a cover on the left, which basically explains the lack of alignment between the chassis and the back. The right side is the only side panel that can be opened by the chassis. It is fixed by four screws. The front end is a vertical row of cooling openings.
The heat dissipating port is responsible for blowing air for the fan behind the front panel. The heat dissipating port is provided with a dust-proof net (accessory, which needs to be affixed to itself).
Swiping off the four screws removes the right side panel. The exposed power cords of various colors hint at the chaotic side hidden in the simple, high-force chassis design language.
Let's take a look at the 1.8mm thickness of the side plate for the internal display of the next chassis.
Remove the panel, eyes back to the chassis, a relatively large relative to the case of the chassis ATX power appears impressively in front of the eyes, of course, the most eye-catching is a bunch of colorful and disorderly power cord trays. The ribs on the fuselage mentioned on the top side (the front ribs of the ribs are two above the front panel; see the figure below is clearer) The SSD is upside down, and the data and power supply lines are aligned. Without a law winding a pass. However, a good face revealed: SanDisk 240G enhanced SSD uses MLC particles in this price segment to ensure stability and longevity. It is mainly used to install systems and software. Here to mention SSD can actually use the side of the screw to install horizontally hidden in the side of the ribs, but personally think that this installation is more convenient to plug wire.
SanDisk Enhanced Edition 240G SSD 649 yuan Jingdong direct link The main board was blocked by power supply for most of the area. The memory was fortunate enough to be red, and it could be looming in the darkness. But the original skull of the brain, called the CPU, in the computer, is completely invisible to Intel's original radiator.
More tragic than it is that I do not put photos I'm afraid that you have not found the Toshiba 3T hard drive, and is kept under pressure by a large power supply, although the difference between the two cards (thickness). Faced with such a sturdy figure, a man with a hard drive would surely think that Nima had inked a year of it and it would be GAY. If a woman should think about it, you are not a man. All right, talking and talking
The Toshiba 3T hard drive has a lower repair rate than the Seagate Western Digital (the sales volume is also low).
Toshiba (TOSHIBA) 3TB 7200 to 64M SATA3 Desktop Hard Drive (DT01ACA300) 579 yuan Jingdong direct link 
Power Supply: The Bestec ATX power supply was removed from the brand's machine. The Taiwan brand is rated at 288W. In addition to the cpu power supply, only a 4PIN interface (although it can still be brought up), other modules, such as wiring, I (wu) not ( Ji) chase (ke) seek (shi), ugly and practical, with a Pentium machine just 
Turned the lens is the original landlord of the chassis - radiator days are not much better ... ... was a pile of power line up the top of the boss, there will be the risk of being stuck at any time, although usually kept blowing ah ... My pride is indulgence... I think the opposite should be like this:
However, looking at the past, everyone is like this:
However, the real heart of the opposite is actually like this:
Once again, haha ​​got it back to normal, because my thoughts of dismantling my internal psychology were disorganized. In the beginning, I almost didn't lose my skin, let alone see my confusion. A pile of power cords, and struggles, lazy cancer finally occupied the upper hand.
Still decided to let the camera work on its behalf, deep inside the chassis to explore the secret: the memory using the odd odd 8G ddr3 1600, red vest is very good, but the performance is generally good cost-effective compatibility is good, the current memory is generally regret not to buy more One step in place.
G.Skill Ripjaws X Series DDR3 1600 8G Desktop Memory 379 yuan Jingdong direct link But now unless the old platform is upgraded, it is not recommended to buy DDR3 memory, and then last DDR4:
G.Skill Ripjaws 4 series DDR4 2400 frequency 8G desktop memory (Bentley black) 379 yuan Jingdong direct link 
On the edge of Intel's original radiator is the CPU: Pentium G3460, low power consumption, performance is also to meet most of the daily applications, not very accounted for the CPU usage of the game can also be brought up. Of course, the G4560 is now the king of choice Pentium, then the price (price) is also close to or even more than I bought this G3460 half price. When the dust on the radiator hasn't been visually dismantled, it's time to stretch out a brush and put it under a little care. G3460 is not recommended here, but G4560 is expensive
Intel Pentium Dual Core G4560 Boxed CPU Processor 429 yuan Jingdong direct link Finally said that the motherboard: Gigabyte B85M-D3H is based on its stability and good expansion performance, but also to leave room for future upgrades. (No photo here) Of course now with the above CPU or to recommend the same as the Gigabyte B150M-D3H
GIGABYTE B150M-D3H motherboard (Intel B150/LGA 1151) 599 yuan Jingdong direct link Another DDR3 version, personal recommendations if you do not have extra DDR3 memory, or step by step to buy the above DDR4 version, but also lay a good foundation for future upgrades.
GIGABYTE B150M-D3H DDR3 motherboard (Intel B150/LGA 1151) 539 yuan Jingdong direct link Of course, the Asus B150M-PLUS can also be selected for the same price segment, followed by a USB Type C,
ASUS B150M-PLUS motherboard Intel B150/LGA 1151619 yuan Jingdong direct link Well, this time, this review has been completed. Thank you.
And so on, what's wrong, I feel like a gust of wind behind me, as if someone is chasing me to ask for a video card...
You are chasing friends, the graphics card has been sold by my friends, the chassis so small, so chaotic, know what happens after loading video card? The top line of the SSD does not speak first, and it is not to be entangled with other types of cables. The most important thing is that in the summer, the internal temperature of the chassis rises significantly due to the temperature of the graphics card, although the video card fan is facing. At the top, but there is no or no cooling fan installed on the top of the chassis. Most of the graphics card's heat cannot be properly guided out. Fans in the chassis and behind the front panel are also turbulent by the wind of the processor's heatsink fan. Gathered in the chassis can not be very effective from the rear cooling outlet and power fan. The most important thing is that the 28cm length of the graphics card is installed in this chassis (29cm installation space). Although it is barely installed, such a large block of bricks is blocked on the top, and the heat flow of the lower processor board cannot be dissipated through the top cooling port. Finally, the temperature of the graphics chip, the processor, and the motherboard are all increased, followed by noise, a slight play of the game, the sound of the processor heat sink and the video card radiator, and the sound of the hard disk reading disk. One group is distracting. This is completely contrary to my concept of installing low power, low heat, low noise and the original intention, so in the end it will be hung on the free fish to sell the card, but fortunately it was the activity price to start, did not make no loss, it is Have a free experience of the moon. Even after removing the video card, the Pentium G3460 still operates in the summer at 45°C+.
This is really the end, this Joe Sibo RM3 chassis, although relatively small in the ATX chassis, but a closer look is also a wide (in order to find the location of the power), although you can install 29CM length and the following graphics card , But these are at the expense of a large degree of heat dissipation and the internal structure of the chassis and the rationality of the layout of the accessories in exchange, such as the power supply is placed on the front of the processor, so that the processor cooling fan facing blowing, which is in the chassis wind It is unreasonable, and even if it is such a confusing wind tunnel, the interior of the chassis is not given enough fans or even the fan installation position. A single front radiator is blown and blown from the front of the right side of the chassis. The narrow heat-dissipation air inlet sends the air to the inside of the chassis. However, more than half of the air should still be circulated from the upper and lower left sides of the chassis to the internal heat flow of the front end of the fan. One half of the blown-out wind is blocked by the front power cable. Form turbulence. So if you want to buy this case, it is recommended to be cautious, unless you really like this shape to non-necessity or only to install Pentium Celeron, a low-power processor and no graphics card, otherwise you must accept it Back to the preparation of a high-value, high-style full-aluminum tin can. However, Qiao Sibo many other chassis is still worth recommending, compared with other brands have a good value and workmanship. U3, for example, is smaller and more structured. I hope that everyone will learn from my (jon) experience (xun) of the current installation. Don't pay attention to the appearance when purchasing the chassis (regardless of the type, whether it is a type of horse or a low-key, restrained type that I prefer). Cultural type), pay more attention to the rationality of the internal structure and style. Too much emphasis on appearance leads to the result like the style of this article, and finally I don't know where I will go...
Of course, in the end, you will find that everything is still a matter of money.
Really. End.
Eleaf Vape pen, Eleaf wholesale, Eleaf disposable vape pen
Shenzhen Xcool Vapor Technology Co.,Ltd , http://www.xcoolvapor.com